Loading...

UTV Class

UTV R

#D1 - D999

Maximum engine size: 2000cc NA, 1001cc Turbo. UTV “R” type vehicles.

Drivers
0
Open Numbers
998
Driver Age
14+

UTV R Rules

Full rulebook

DEFINITION

Two or four-seat UTV “R” vehicles as produced by the manufacturer. Maximum engine size: 2000cc NA, 1001cc Turbo. Any manufacturer UTV may be used providing the model used has been series produced in a minimum of 1000 units within a twelve (12) month period.

GENERAL REGULATIONS

Entrants in this class shall comply with all applicable general regulations.

TECHNICAL REGULATIONS

This class is a limited class, and all components will be considered restricted unless unrestricted herein. This is a non-pro class.

NOTE: The UTR abbreviations listed under this class (I.E. UTR1 HELMETS) refer to UTR cross reference listings in the front of this book. These UTR cross-referenced listings are part of the class rules. Where a conflict occurs between the UTR cross-referenced listing and a rule contained under this class, the rule contained under this class takes priority.

SAFETY EQUIPMENT

UTR1 HELMETS

See UTR1 in UTV Technical Rules.

UTR2 PROTECTIVE CLOTHING

See UTR2 in UTV Technical Rules.

UTR3 EYE PROTECTION and DENTURES

See UTR3 in UTV Technical Rules.

UTR4 HEAD AND NECK RESTRAINTS

See UTR4 in UTV Technical Rules.

UTR5 FIRST AID KIT

See UTR5 in UTV Technical Rules.

UTR6 EMERGENCY SIGNALING DEVICES

See UTR6 in UTV Technical Rules.

UTR7 HORNS

See UTR7 in UTV Technical Rules.

UTR8 REFLECTORS

See UTR8 in UTV Technical Rules.

UTR9 FIRE SUPPRESSION EQUIPMENT

See UTR9 in UTV Technical Rules.

UTR10 SURVIVAL SUPPLIES

See UTR10 in UTV Technical Rules.

SUSPENSION COMPONENTS

Track Width: 83". Measured outside of tire to outside of tire at ride height, at its widest point.

Wheelbase: Stock, as delivered by the manufacturer, plus eight (8) inches.

Pivot Points: Wheelbase is measured from the center of front wheels to the center of rear wheels. Must remain plus or minus 8” of OEM 2 or 4 seat approved manufacturers vehicles.

This can be achieved either through the suspension arms or cutting and adding to the OEM Chassis. All seams must be sleeved and rosette welded plus gussets. If a full replica to OEM Chassis is used all pivot points on front and rear will remain in the OEM location.

You cannot raise or lower rear trailing arm pivots and radius rod pivots must remain in OEM location. Shock mounts can be relocated if longer arms are used but must remain on the same arm as delivered from manufacture. This will be the only pivot point allowed to be relocated in the front or rear clip.

Suspension Components (Suspension components, A-arms, spindles, links, bushings, etc.): Open. Must retain the stock concept, dual A-arm, I-beam, trailing arm, etc.

Ball Joints: Ball joints may be of any manufacturer.

Sway Bars: Open.

Sway Bar Links: Open.

Radius/Tie Rods: Open.

Hubs & Wheel Bearings: Open.

Axles/CV Joints: Open.

UTR11 SHOCK ABSORBERS and BUMP STOPS

Limited to one shock per wheel.

No external bypass shocks.

Stock shock mounts may be reinforced or replaced. Shock mounting position is open.

Solid bump stops only. No air/hydraulic bump stops allowed.

UTR12 SECONDARY SUSPENSION

No secondary suspension allowed.

Sway bar links are open.

UTR13 WHEELS and TIRES

Wheel diameter is sixteen (16) inch maximum.

Maximum tire size is 35x10.5.

Wheel studs are open.

UTR14 FASTENERS

See UTR14 in UTV Technical Rules.

STEERING and BRAKE COMPONENTS

UTR15 STEERING

Power Steering: Open. No full Hydraulic Steering. Hydraulic assist allowed.

Steering / Turning Brakes: Not allowed.

Steering Box: Open.

Knuckles: Open.

Spindles: Open.

Center Steering: Open.

Steering Tie Rods: Open.

Steering Wheel: Open.

UTR16 BRAKES

Open.

ELECTRICAL SYSTEM

UTR17 IGNITION

See UTR17 in UTV Technical Rules.

UTR18 BATTERIES

See UTR18 in UTV Technical Rules.

UTR19 LIGHTS

See UTR19 in UTV Technical Rules.

UTR20 STARTERS

See UTR20 in UTV Technical Rules.

FUEL SYSTEM

Pressurized fueling systems not allowed. Gravity fueling, dump cans or fuel towers only.

UTR21 FUEL

Any commercially available unleaded gasoline with a maximum of 10.0 percent oxygen content may be used. No additives, blending or modifying of fuel in any manner. Commercially available Ethanol i.e., E85, C85 or C95 is not allowed. No alcohol or nitromethane is allowed. No alcohol may exclude some pump gasolines in some states. American Off-Road Racing Championship may take Fuel samples at random before, during, and after the event.

UTR22 FUEL TANKS

See UTR22 in UTV Technical Rules.

UTR23 FUEL FILLERS LINES, VENTS, and CAPS

See UTR23 in UTV Technical Rules.

ENGINE, TRANSMISSION and DRIVELINES

Engine: All engines must retain OEM blocks and cylinder heads. Stock bore and stroke must be retained. All internal engine parts are open. Engine must remain in the stock location.

Engine Displacement: Maximum engine size 2000cc NA, 1001cc Turbo.

Intake Manifold: OEM.

Throttle Body: OEM.

Air Cleaners: Open.

Air Cleaner Tubes: Open.

Fuel Injectors: Open.

Clutches: Open.

Fuel Pumps: Open.

Fuel Regulators: Open.

Fuel Filters: Open.

Fuel Rails: Open, must be made of metal.

Springs & Weights: Open.

Clutch housing cooling inlet and outlet tubes (snorkels): Open.

Differentials: Front and rear differential cases must remain stock.

Sheaves, Sliders, Rollers: Open.

Clutch Ducting: Open.

ECU: Open.

Intake Ducting: Open.

Boost Tube: Open.

Intake Tube: Open.

BOV: Open.

UTR25 ENGINE REPLACEMENT

See UTR25 in UTV Technical Rules.

UTR26 TRANSMISSION/DIFFERENTIAL

Transmission/Gear Box Cases: Stock, as delivered by the manufacturer. Internal modifications open.

Reverse Gear Function: All vehicles are required to have functional reverse gear.

Differential Cases: Front and rear differential cases must remain stock, as delivered by the manufacturer. Internal modifications open.

Side Covers: Open.

Axle Flanges: Open.

Bearings: Open.

Retainer Plate: Open.

High Gear Spacers: Open.

UTR27 THROTTLES

OEM

UTR28 EXHAUST

Open.

UTR29 DRIVE SHAFTS

Open.

UTR30 FLYWHEEL SHIELDS

See UTR30 in UTV Technical Rules.

UTR31 FLUID COOLERS

Open.

UTR32 AUXILIARY EQUIPMENT

See UTR32 in UTV Technical Rules.

UTR33 SUPERCHARGERS and TURBOCHARGERS

Production-Only Equipment Turbochargers and Superchargers must remain unmodified and identical to those produced by the factory or sold to the public with an OEM (Original Equipment Manufacturer) part number. Only 1001cc engines can be fitted with OEM turbo chargers. All OEM turbo chargers must be approved by American Off-Road Racing Championship.

VEHICLE SAFETY EQUIPMENT

UTR34 ROLL CAGES

See UTR34 in UTV Technical Rules.

UTR35 SAFETY HARNESS

See UTR35 in UTV Technical Rules.

UTR36 SAFETY NETS

See UTR36 in UTV Technical Rules.

UTR37 SEATING

Race seats only. All stock seats must be removed.

GENERAL VEHICLE COMPONENTS

UTR38 DRIVER'S COMPARTMENT

Metal firewalls protecting occupants from fire, fuel, and liquids are required.

Metal firewalls, steel or aluminum must be .040 thick minimum.

Any pass-through holes required must be kept to a minimum.

UTR39 DOORS AND LATCHES

No opening doors are allowed. All door openings must be braced with 1.5x.095 tubing minimum. All door openings must be covered with metal .060 thick minimum.

UTR40 FIREWALLS

See UTR40 in UTV Technical Rules.

UTR41 BALLAST

See UTR41 in UTV Technical Rules.

UTR42 WEIGHT

See UTR42 in UTV Technical Rules.

UTR43 FLOORBOARDS

See UTR43 in UTV Technical Rules.

UTR44 BUMPERS and HAZARDOUS PROTRUSIONS

See UTR44 in UTV Technical Rules.

UTR45 MIRRORS

See UTR45 in UTV Technical Rules.

UTR46 SKID PLATES

See UTR46 in UTV Technical Rules.

UTR47 STORAGE

See UTR47 in UTV Technical Rules.

UTR48 CHASSIS and BODY

Chassis/Body: Open. Must retain the appearance of a production UTV. Stock grills are mandatory.

Lower Frame Rail: Open.

Frame Rail Reinforcement: Frame rails may be reinforced and or replaced, but stock length and width must be retained, as delivered by the manufacturer.

Approval: All frames and bodies subject to American Off-Road Racing Championship approval.

Roof: Roof must be covered with sheet metal .060 thick minimum.

Seats: Open.

Additional Tubes & Gussets: Open.

Body Components: Open. Must have the appearance of a production UTV.

Spare Tire Mount: Open.

UTR49 HOSES

See UTR49 in UTV Technical Rules.

UTR50 IDENTIFICATION MARKINGS

See UTR50 in UTV Technical Rules.

UTR51 ADVERTISING on VEHICLES

See UTR51 in UTV Technical Rules.

UTR52 RADIO EQUIPMENT

See UTR52 in UTV Technical Rules.

UTR53 WORKMANSHIP

See UTR53 in UTV Technical Rules.

UTR54 TRACKING DEVICE

See UTR54 in UTV Technical Rules.

UTV R Drivers

0 drivers

No drivers have registered a vehicle in this class yet.

More UTV Classes

Looking for More?

Compare every class, or check the full rulebook for the technical rules referenced above.

Unlimited Off-Road Racing

The Unlimited Off-Road Racing league was formed by The Martelli Brothers in 2023 after more than a decade of successful desert off-road race promotion, including The Mint 400, The UTV World Championship and The California 300. The league was formed to promote the sport of desert off-road racing, the off-road industry, and to expand the reach of off-road companies beyond the industry and into the homes of every off-road race fan, globally. Key attributes of the newly formed league include large racer car counts, competitive and challenging race courses, safe and family-friendly spectating areas, multiple days of racing and off-road festivities all located near major cities and markets that positively affect the off-road industry. The Martelli Brothers, owners of the motorsports powerhouse production group Mad Media have made it their mission to grow the league into a four race series that showcases the best off-road racers on the best courses in North America.

© 2026 Terranaut Media Group. All rights reserved.