UTV Pro Super Stock Turbo KT001 - KT999
Limited Turbo Charged UTV.
2024 Class Consolidation
Limited Turbo Charged UTV.
DEFINITION
Two seat vehicles built using a production UTV. Any manufacture UTV may be used providing the model used has been series produced in a minimum of 1000 units within a twelve (12) month period. Maximum engine size 1000cc. Engines/Turbos must remain stock as delivered by OEM. Stock production body parts required.
GENERAL REGULATIONS
Entrants in this class shall comply with all applicable general regulations.
TECHNICAL REGULATIONS
This class is a limited production class, and all components will be considered restricted unless unrestricted herein.
NOTE: The UTR abbreviations listed under this class (I.E. UTR1 HELMETS) refer to UTR cross reference listings in the front of this book. These UTR cross-referenced listings are part of the class rules. Where a conflict occurs between the UTR cross-referenced listing and a rule contained under this class, the rule contained under this class takes priority.
SAFETY EQUIPMENT
UTR1 HELMETS
UTR2 PROTECTIVE CLOTHING
UTR3 EYE PROTECTION and DENTURES
UTR4 HEAD AND NECK RESTRAINTS
UTR5 FIRST AID KIT
UTR6 EMERGENCY SIGNALING DEVICES
UTR7 HORNS
UTR8 REFLECTORS
UTR9 FIRE SUPPRESSION EQUIPMENT
UTR10 SURVIVAL SUPPLIES
SUSPENSION COMPONENTS
Must retain stock pivot points as delivered by the manufacturer. Suspension pivot points may be reinforced but must remain in stock location. All pivot points will be used as designed by the manufacturer. No pivot points may be added or removed.
Suspension components may be of any manufacturer, must bolt to stock pivot points. Suspension joint type open i.e ball joint, rod end, spherical bearing. A-arms may be lengthened to the widest width supplied by the vehicle manufacture.
Maximum track width as measured outside of tire to outside of tire at ride height is eighty (78) inches.
Wheelbase is restricted to stock plus or minus three (3) inches.
UTR11 SHOCK ABSORBERS and BUMP STOPS
Must have one shock per wheel in working condition at start of event.
Limited to one shock per wheel.
Upper stock shock mounts may be reinforced but must remain in stock location. Lower shock mounting position is open.
No remote mounted shocks.
Solid bump stops only. No air/hydraulic bump stops allowed.
UTR12 SECONDARY SUSPENSION
No secondary suspension allowed.
Sway bar links are open.
UTR13 WHEELS and TIRES
Wheel diameter is fifteen (15) inch maximum.
Maximum tire size is 33x10.5x15.
Vehicle race number must be stamped on to all wheels. Minimum stamp size is ¼” (.250) inches.
UTR14 FASTENERS
STEERING and BRAKE COMPONENTS
UTR15 STEERING
OEM power steering boxes only. Steering rack is open, must bolt to stock mounts in the stock location.
No steering or turning brakes allowed.
UTR16 BRAKES
Stock OEM brakes mounted in stock location. Brake pads are open.
ELECTRICAL SYSTEM
UTR17 IGNITION
All OEM engine electronics must be used. No aftermarket ECU’s. Stock ECU’s may be re-flashed.
UTR18 BATTERIES
Batteries and locations are open. All batteries mounted in the drivers compartment must be sealed enclosure. All batteries must be securely mounted. Battery shut off switch is required.
UTR19 LIGHTS
All vehicles must have a minimum of two(2) taillights and two(2) brake lights. Tail and brake lights must be 3 inch in diameter. All UTV's must also have four(4) additional rear facing safety lights. One(1) solid amber, one(1) flashing amber, one(1) solid blue, and one(1) flashing blue. All safety lights must be LED with a minimum of 2000 lumens output. All safety lights must be wired directly to the battery switch. All lights must be mounted 48 inches from the ground minimum. Safety lights must be on at all times. Vehicles without working safety lights will not be allowed to leave the starting line or pass through a check point. All light subject to Unlimited Off-Road Racing approval.
UTR20 STARTERS
FUEL SYSTEM
UTR21 FUEL
UTR22 FUEL TANKS
UTR23 FUEL FILLERS LINES, VENTS, and CAPS
Stock fuel tank in the stock location. Fuel cell may be relocated to any location. Maximum fuel capacity is 15 gallons.
ENGINE, TRANSMISSION and DRIVELINES
UTR24 ENGINE and ENGINE DISPLACEMENT
Maximum engine displacement is 1000cc.
Engine cases and heads must remain stock as delivered by the manufacture.
All engine components must remain stock.
Header pipes, mufflers are open.
Fuel pumps, fuel regulators, fuel injectors, throttle bodies must remain OEM as delivered by the manufacture.
Stock OEM air boxes, air lines and charge tubes must be used. Air cleaner may be of any manufacturer.
Engine must remain in stock location.
UTR25 ENGINE REPLACEMENT
UTR26 TRANSMISSION
Transmission/gear box cases must remain stock.
All vehicles are required to have a functional reverse gear.
Front and rear differential cases must remain stock.
Any aftermarket direct bolt on clutch may be used.
Clutch spring rates are open.
UTR27 THROTTLES
UTR28 EXHAUST
Open
UTR29 DRIVE SHAFTS
Axle shafts are open. CV joints are open, must fit stock OEM stub axles.
UTR30 FLYWHEEL SHIELDS
UTR31 FLUID COOLERS
No add on coolers.
UTR32 AUXILIARY EQUIPMENT
UTR33 SUPERCHARGERS and TURBOCHARGERS
Turbo and all components must remain stock as delivered by the OEM.
VEHICLE SAFETY EQUIPMENT
UTR34 ROLL CAGES
Stock production roll cages are not allowed.
UTR35 SAFETY HARNESS
UTR36 SAFETY NETS
UTR37 SEATING
Race seats only. All stock seats must be removed.
GENERAL VEHICLE COMPONENTS
UTR38 DRIVERS COMPARTMENT
Metal firewalls protecting occupants from fire, fuel, and liquids are required. Metal firewalls, steel or aluminum must be .040 thick minimum. Any pass-through holes required must be keep to a minimum.
UTR39 DOORS AND LATCHES
No opening doors allowed. All door openings must be braced with 1.5x.095 tubing minimum. All door openings must be covered with metal .060 thick minimum.
UTR40 FIREWALLS
UTR41 BALLAST
UTR42 WEIGHT
UTR43 FLOORBOARDS
UTR44 BUMPERS and HAZARDOUS PROTRUSIONS
Safe front and rear bumpers required. No shape corners or hazardous protrusions.
UTR45 MIRRORS
UTR46 SKID PLATES
UTR47 STORAGE
UTR48 CHASSIS and BODY
Stock Chassis as delivered by the manufacture must be retained.
Chassis may be reinforced but all stock OEM components must be retained.
Stock grill, hood, dash, inner tub and front and rear fenders must be used.
All Stock OEM body parts must be used as delivered from the manufacture.
Minimum notching for roll cage and bumpers allowed.
Roof must be covered with sheet metal .060 thick minimum.
UTR49 HOSES
UTR50 IDENTIFICATION MARKINGS
Unlimited Off-Road Racing will assign race numbers.
UTR51 ADVERTISING on VEHICLES
UTR52 RADIO EQUIPMENT
UTR53 WORKMANSHIP
UTR54 TRACKING DEVICE
UTV Pro Super Stock Turbo Drivers
2023 UNLTD Off-Road Racing Triple Crown Points Standings
| Driver | 2023 King of the Hammers | 2023 BFGoodrich Tires Mint 400 | 2023 California 300 | Total | Position |
|---|---|---|---|---|---|
| Sara Price | 125.00 | 187.50 | 250.00 | 562.50 | 1st |